Clay Nodes

sixteensixty4 · Post by **sixteensixty4** » Thu Nov 03, 2011 12:01 am

Just curious, i know they regrow after a while, but is it possible to dig a clay node so low that it never comes back?

Malicious · Post by **Malicious** » Thu Nov 03, 2011 12:04 am

Nope.

sixteensixty4 · Post by **sixteensixty4** » Thu Nov 03, 2011 12:29 am

cool, brick-walling and was little worried about that, thanks!

ImAwesome · Post by **ImAwesome** » Thu Nov 03, 2011 1:37 am

don't exhaust a good node for a brickwall, quality doesn't matter for buildings. if there is a crappy node nearby use that.

sixteensixty4 · Post by **sixteensixty4** » Thu Nov 03, 2011 5:52 pm

yeah it was only a crappy node, but on doorstep which is pretty handy, after 11k+ bricks so its taking a long time

Azadon · Post by **Azadon** » Tue Nov 08, 2011 1:43 pm

I have a related question. Let's say you are on a decent node, say Q50, and on the edges it's Q15. If you dig on the edge at the Q15 area, does that lower the Q50 stuff? If so, by how much? Point for point? If you go out to where it's Q10 but can keep digging, would that lower the Q50 stuff?

Lopezruy · Post by **Lopezruy** » Tue Nov 08, 2011 4:03 pm

Azadon wrote:I have a related question. Let's say you are on a decent node, say Q50, and on the edges it's Q15. If you dig on the edge at the Q15 area, does that lower the Q50 stuff? If so, by how much? Point for point? If you go out to where it's Q10 but can keep digging, would that lower the Q50 stuff?

I am pretty sure that if its a Q50 node, it will stay a Q50 node, no matter what you do to the Q15 & Q10 nodes.

Maulkin · Post by **Maulkin** » Tue Nov 08, 2011 4:23 pm

that is not exactly true. If you dig anywhere in a node, you'll lower the quality of the whole node. the speed of how i depletes might be slower than if you dig the sweet spot itself, but it does deplete

Azadon · Post by **Azadon** » Tue Nov 08, 2011 5:52 pm

Lopezruy wrote:
Azadon wrote:I have a related question. Let's say you are on a decent node, say Q50, and on the edges it's Q15. If you dig on the edge at the Q15 area, does that lower the Q50 stuff? If so, by how much? Point for point? If you go out to where it's Q10 but can keep digging, would that lower the Q50 stuff?
I am pretty sure that if its a Q50 node, it will stay a Q50 node, no matter what you do to the Q15 & Q10 nodes.

Yeah, like the next poster said, I'm talking about one node: Q50, but on the edges of it where it is as low as it goes and is still part of the node. If I dig at the edge for crappy wall-building clay, is it going to affect the Q50 stuff? If so, how much?

Malicious · Post by **Malicious** » Tue Nov 08, 2011 6:03 pm

Azadon wrote:
Lopezruy wrote:
Azadon wrote:I have a related question. Let's say you are on a decent node, say Q50, and on the edges it's Q15. If you dig on the edge at the Q15 area, does that lower the Q50 stuff? If so, by how much? Point for point? If you go out to where it's Q10 but can keep digging, would that lower the Q50 stuff?
I am pretty sure that if its a Q50 node, it will stay a Q50 node, no matter what you do to the Q15 & Q10 nodes.
Yeah, like the next poster said, I'm talking about one node: Q50, but on the edges of it where it is as low as it goes and is still part of the node. If I dig at the edge for crappy wall-building clay, is it going to affect the Q50 stuff? If so, how much?

It will slowly lower it over time.
It's a good trick to dig the lowest quality spot until it's empty and move closer and closer to the node.
You'll get more clay this way so it's perfect for building walls.

Clay Nodes

Clay Nodes

Re: Clay Nodes

Re: Clay Nodes

Re: Clay Nodes

Re: Clay Nodes

Re: Clay Nodes

Re: Clay Nodes

Re: Clay Nodes

Re: Clay Nodes

Re: Clay Nodes